Guide

Where Should CO2 Monitors Be Placed?

Updated on · By the Zyentia team

Place a CO2 monitor at breathing height in the room where people spend the most time, about 3 to 5 feet off the floor and at least 3 feet from windows, doors, vents and outside walls. Keep it out of direct sun and away from drafts so it reads the air people actually breathe.

On this page (12 sections)
  1. Where should CO2 monitors be placed in a room?
  2. Why should a monitor stay away from windows, doors and vents?
  3. Where does a CO2 monitor go in a bedroom?
  4. Should you place a monitor in the kitchen or bathroom?
  5. How do you place a monitor in an open-plan or large room?
  6. Can you wall-mount a CO2 monitor, and where?
  7. Where should you not put a CO2 monitor?
  8. Does the sensor type change where you place a monitor?
  9. How long should a monitor settle after you move it?
  10. Where should CO2 monitors be placed if you only own one?
  11. What is the best spot for a CO2 monitor in a home office?
  12. Which spot should you pick first?

Place a CO2 monitor at breathing height in the room where people spend the most time, about 3 to 5 feet off the floor. Keep it at least 3 feet from windows, doors, vents and outside walls, out of direct sun and away from drafts.

That way it reads the air people actually breathe, not the air next to a leaky window. A reading only means something when the sensor sits in the right spot.

Put it in the wrong place and you'll see numbers that look fine while the room feels stuffy, or numbers that spike because a draft is pushing outdoor air past the sensor.

The short answer to where should CO2 monitors be placed is simple: match the monitor to the room's breathing zone and keep it away from anything that moves air quickly.

Where should CO2 monitors be placed in a room?

Put the monitor in the breathing zone of the room you want to judge, roughly 3 to 5 feet above the floor. That is the band where seated, standing and sleeping people draw air, so it gives the most useful picture of what they are actually breathing.

CO2 is slightly heavier than air, but in a normal room with people moving and warm air rising, it mixes fairly evenly. You don't need to hang a monitor from the ceiling or set it on the floor.

A side table, a shelf or a wall mount at chest or head height is close enough. Pick the spot where the room's air is representative.

The middle of a living room or the corner of a home office works better than a spot jammed against a wall or behind a sofa.

Leave a few inches of clear space around the sensor vents so air can reach the inlet.

Why should a monitor stay away from windows, doors and vents?

Windows, doors and HVAC vents move air fast enough to skew the reading. A monitor beside an open window samples outdoor air at about 420 ppm, so it will report a low number even when the rest of the room is stale.

A vent blowing conditioned air does the same thing in reverse.

The fix is distance. Keep the monitor at least 3 feet from any window, exterior door, supply vent, return grille or ceiling fan.

That gap lets the sensor sample room air rather than the stream passing by it.

Drafts matter too. A monitor near a gap under a door or beside an air conditioner can swing by hundreds of ppm as the draft turns on and off.

If you want to test whether a room is ventilated, place the monitor in the calm part of the room, not next to the opening you're testing.

Where does a CO2 monitor go in a bedroom?

Set it on a nightstand or shelf at head height, a couple of feet from the pillow and away from the window and any radiator or vent. The bedroom is the room where CO2 matters most, because people sleep with the door and window closed for hours.

A monitor at mattress height reads the air you breathe overnight.

Many people wake with a stuffy feeling when the bedroom CO2 climbs past about 1,500 ppm, and a monitor in the breathing zone shows whether the room clears when the door opens in the morning. Place it so you can read the display from bed without moving it.

Avoid putting it under the covers or on the floor beside the bed. A monitor buried in bedding traps air and reads too high.

One on the nightstand with clear space around it is the practical choice.

Our guide to what is a good CO2 reading explains the numbers you'll see overnight.

Which monitor suits a bedroom?

The Aranet4 is the pick for a bedroom because its e-ink display stays readable and it runs on 2 AA batteries for up to 4 years. The NDIR sensor measures CO2, temperature, relative humidity and atmospheric pressure, and the free app keeps up to 90 days of history so you can review how the room clears each night.

Should you place a monitor in the kitchen or bathroom?

Yes, but only for short checks, not for permanent readings. Cooking with a gas hob and running a hot shower both push CO2 and moisture into the air, and a monitor in the breathing zone shows how fast the room clears when you turn on the extractor fan.

Place it on a counter or shelf at chest height, away from the hob, the oven and the extractor hood. Steam and heat near the sensor can affect both the CO2 reading and the humidity figure.

Keep it at least 3 feet from the fan intake.

Don't leave a monitor in the bathroom permanently. Condensation on the sensor vents is not good for any electronics, and a closed bathroom with the fan off is not the room you need to judge day to day.

A short reading before and after a shower tells you what you need.

How do you place a monitor in an open-plan or large room?

Place it where people sit, not in the middle of the floor plan. An open-plan kitchen and living area has pockets of different air, and the monitor should sample the pocket where people spend time.

A monitor on the dining table or beside the sofa reads the shared air.

One near the kitchen extractor reads cleaner air than the sofa corner.

If the room is very large, consider two monitors or move one between the main seating area and the kitchen. Height still matters.

A shelf at eye level when seated is better than a spot on top of a tall cabinet. Air near the ceiling is warmer and often staler, so a high perch can read higher than the air people breathe.

Can you wall-mount a CO2 monitor, and where?

Yes, and a wall mount is a good option for a room where the monitor would otherwise sit on a table. The SwitchBot CO2 Monitor has wall-mount holes and an adjustable bracket, so it can hang or stand upright at 42° or 90°.

A spot on an interior wall at about 4 feet is a practical mount height. Mount it away from outside walls, which can be cooler and cause local air movement.

Keep it clear of doorways and light switches that people touch often. The display should be easy to read without standing on a chair.

A wall mount also keeps the monitor out of reach of children and pets. Just leave a few inches of clear space around the sensor vents so the wall doesn't block airflow.

The SwitchBot's large 92 mm screen displays CO2, temperature, humidity, time and comfort level at once.

Which monitor works well on a wall?

The SwitchBot CO2 Monitor fits wall mounting with its included bracket. Its Swiss-made NDIR sensor measures CO2 from 400 to 9,000 ppm every 1 second, with an accuracy of ±50 ppm.

The built-in battery lasts up to 12 months.

Where should you not put a CO2 monitor?

Avoid anywhere that traps air or puts the sensor in a stream. A closed cabinet, a drawer, a shelf pressed against a wall or a spot under a desk all give readings that don't match the room.

The same goes for direct sunlight, which heats the case and skews the temperature and humidity figures.

Other spots to skip:

  • On top of a fridge or freezer, where warm air rises and the motor vibrates.
  • Right beside a humidifier, which pushes moisture and air past the sensor.
  • Next to a door that opens to the outside, where the reading swings all day.
  • Outdoors or in a garage, unless the monitor is rated for it.

The sensor needs steady room air to do its job. If the number moves sharply every few minutes, the monitor is probably sitting in a draft or next to a vent.

Move it to a calmer spot and let it settle.

Does the sensor type change where you place a monitor?

No, but it changes how much you should trust a quick reading. The NDIR sensor inside most good monitors, including the three here, needs a steady sample of room air.

The what is NDIR sensor guide explains how the sensor works, and why a monitor placed in a draft can report lower numbers than the room really has.

The GoveeLife H5140 uses an SCD4x CO2 sensor on the photoacoustic NDIR principle. Its 5-second refresh rate and built-in pressure compensation mean it settles quickly after a move.

Place it on a shelf at breathing height near where people sit.

Because the GoveeLife runs on AC power, it suits a fixed spot near an outlet rather than a spot you move often. The Aranet4 and SwitchBot run on batteries, so they are easier to carry between rooms.

How long should a monitor settle after you move it?

Give it 5 to 15 minutes in the new spot before you trust the number. A monitor moved from a stuffy bedroom to a living room carries its old reading in the sensor chamber, so the display can lag for a few minutes.

Let it sit undisturbed while it settles.

Don't breathe on it, wave a hand near the vents or open a window during this time.

Once the reading holds steady for a few minutes, it's showing the new room. If you move a monitor between rooms to compare them, keep the test fair.

Measure at the same height and at the same time of day, with the same number of people in each room.

A quick comparison of CO2 monitors for home options can help you decide whether one unit is enough.

Where should CO2 monitors be placed if you only own one?

Move it to the room you care about most, and judge one room at a time. For most homes that means the bedroom overnight and the home office or living room during the day.

A single well-placed monitor gives you more useful data than three badly placed ones.

Start with the bedroom. Run it for a few nights, then move it to the room where you spend the most waking hours.

If a room reads high, open a window or door and watch how fast the number falls. That tells you whether the room's ventilation is working.

A portable CO2 monitor makes this easier, because you can carry it from room to room without unplugging anything. A fixed unit near an outlet is fine if you only care about one room.

What is the best spot for a CO2 monitor in a home office?

Put it on the desk or a shelf at seated head height, away from the window and the door. Small rooms with one person and a closed door are where CO2 climbs fastest, so the monitor needs to sit where you actually breathe.

Place it beside the monitor or on a corner of the desk, not in front of a fan or beside a laptop exhaust.

A spot about 2 to 3 feet from your face reads the air you're breathing without catching your own breath directly. Leave a few inches of clear space around the sensor.

If the reading climbs past about 1,000 ppm while you work, crack a window or door. A monitor in the breathing zone shows whether that fix works.

Our roundup of portable CO2 monitors covers units you can move between the desk and the bedroom.

Which spot should you pick first?

Pick the bedroom or the room where people spend the most hours, and place the monitor at breathing height with clear space around it. That single spot answers the question for most homes, because it is the room where CO2 matters most and where a high reading is easiest to fix.

Keep the monitor at least 3 feet from windows, doors and vents, out of direct sun and away from drafts. Give it a few minutes to settle after any move.

Then use the number to decide when to open a window, not to chase a perfect reading.

If you want a unit that travels easily between rooms, the Aranet4 is the best pick for most homes thanks to its battery life and app history. The SwitchBot suits a wall mount and the GoveeLife suits a fixed spot near an outlet.

Compare CO2 monitors for home use before you choose, and read what a good CO2 reading looks like so you know when to act.

Frequently asked questions

Should a CO2 monitor go near the floor or near the ceiling?

Neither. CO2 mixes fairly evenly in a room with normal air movement, so the most useful height is the breathing zone, about 3 to 5 feet up.

A monitor on the floor or up on a high shelf reads air that people rarely breathe.

Can I place a CO2 monitor in a closed cabinet?

No. A cabinet traps air and blocks the sensor, so readings climb or lag behind the room.

Place the monitor in open air on a table, shelf or wall mount, with a few inches of clear space around the vents.

How many CO2 monitors does a home need?

One monitor per room you want to judge is the simplest approach. If you own a single unit, move it between the bedroom, living room and home office, letting it settle for a few minutes in each spot before you trust the number.

Does a CO2 monitor need to be near the people in the room?

Yes, within the same air space. A monitor across the room still reads the general level, but a spot close to where people sit or sleep catches rising CO2 sooner.

Avoid placing it so close that someone breathes straight onto the sensor.